- #Silicon image 3124 sataraidmanager install#
- #Silicon image 3124 sataraidmanager serial#
- #Silicon image 3124 sataraidmanager driver#
- #Silicon image 3124 sataraidmanager manual#
As the BIOS boots press Ctrl+R when prompted to enter the RAID BIOS. JBOD will destroy existing data on the hard drive.
4ĥ JBOD This RAID array to be used on New/Blank hard drives. Continue with the Fdisk and Format steps as if you were installing a conventional hard drive. When asked Are You Sure to Exit(Yes/No)?, select Yes, then press Enter to exit and reboot. When asked, Activate load balance for RAID 1 (Yes/No)?, select Yes, then press Enter. Create name or leave blank, then press Enter. At the next screen choose RAID1, then press spacebar. At the next screen select RAID, then press Enter. Mirroring will destroy existing data on the hard drives. RAID 1 (Mirror) This RAID array to be used on New/Blank hard drives. When asked Expand RAID 0 to maximum capacity, select No, then press Enter. Select chunk size from 8k, 16k, 32k, 64k, 128k or 256k, then press spacebar. Striping will destroy existing data on the hard drives. RAID 0 (Striping) This RAID array to be used on New/Blank hard drives. RAID Arrays RAID Arrays are setup in the SATA II-150 PCI RAID BIOS. It's possible to combine hard drives of different sizes and makes, however, it is not recommended to do so. It is recommended use identical hard drives for all RAID configurations.
#Silicon image 3124 sataraidmanager serial#
Hard Disk Drive Connection The SATA II-150 PCI RAID is a two channel Serial ATA controller that supports two Serial ATA hard disk drives. Replace the computer cover and reconnect the power cord. Replace the slot bracket holding screw to secure the card. Push the board down firmly, but gently, until it is well seated.
#Silicon image 3124 sataraidmanager install#
To install the card, carefully align the card's bus connector with the selected PCI slot on the motherboard. Remove the slot bracket from an available PCI slot.
Unplug the power cord from the back of the computer, remove the cover. Turn OFF the power to your computer and any other connected peripheral devices. Avoid contact with internal parts and handle cards only by their external edges. Discharge any static electricity build up in your body by touching your computer s case for a few seconds. Static electricity discharge may permanently damage your system.
#Silicon image 3124 sataraidmanager manual#
Since the design of computer cases and motherboards vary, refer to your computer s reference manual for further information, if needed. SATA II-150 PCI RAID Hardware Installation General instructions for installing the card are provided below.
#Silicon image 3124 sataraidmanager driver#
Features and Benefits Compliant with PCI 2.3 Compliant with Serial ATA 1.0 specifications and complement of SATA II optional features Supports RAID 0 (stripe) for performance and RAID 1 (mirror) for data protection Supports two SATA channels and data transfer rate up to 1.5Gb/s (150MB/s) Supports Native Command Queuing (NCQ) and SATA TCQ commands Onboard bus master engine relieves the system processor and enhances system performance Features independent 256-byte FIFOs per channel for host reads and writes Breaks the 137GB barrier! Works with various brands of large capacity Serial ATA hard disks Supports SATA hard disk hot-plugging System Requirements Pentium or equivalent PC with an available PCI slot Windows 2000 / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / Vista (32-/64-bit) C 1Ģ Package Contents SATA II-150 PCI RAID board 2 SATA data cables and one dual-connector SATA power cable Spare low profile bracket Driver CD and Quick Installation Guide Layout HDD LED pins (Front chassis LED connects horizontally) Internal connectors HDD Activity LEDs Figure 1. 1 SATA II-150 PCI RAID Quick Installation Guide Introducing the SATA II-150 PCI RAID The SATA II-150 PCI RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI enabled systems.
0 kommentar(er)
